Saturday 25 November 2017

The kitchen goes in and grumbling goes on

 There will be a considerable amount of grumbling in this post for which I apologise in advance.  This blog is supposed to be my own record/journal/diary of this build and should, therefore, try to be recorded warts and all.  This week there are many warts.  Sharing them is no bad thing as they may serve to remind someone here and there not to do the same.

Let's start with nice!  Here are two more pieces for my bedroom from Elf Miniatures.  There is a small table to be used as a desk and a bedside cabinet to match the three piece bedroom suite I had already bought.  The drawer does open and the finish is lovely.



The desk is to sit in the dormer window space so it was made specially for me so I could have an exact fit.




Bedroom wart:  I do wish I had thought to cut the wallpaper so that the trees didn't have their heads chopped off where the wall joins the ceiling.



When the roof is down this is what you will see through the dormer window.

-------------------------------------------------------------------------------------------------------------------------

Let's wart away in the kitchen.


I tried to improve the tiles by adding a thin card paper trim down the side as they would have a trim in real life.  I also coated them with a triple thick glaze which is something of a pain to apply to a large area.  I do commend it to you if you have a clock face or something like that which you would like to have the appearance of being covered in glass.  It works really well and even gives that nice domed effect that clock glass has.  It works best by dropping a generous amount into a space and letting it settle




The tiles were them re-scored carefully and I kidded myself they looked better for it and they were put in place.


The left side of the kitchen is a double wart wall.

Wart number one:  Why, oh why after making the boob of putting in trim in the bedroom and then realising I should have put the false door in first did I then go on to trim the kitchen and then add the extractor fan!  I didn't even realise it until everything was in place and then the penny dropped the extractor does not go to the ceiling it only goes to the coving!!!!!!!!  I can''t face removing and fixing right now so there it will stay for a while.

Wart number two:  the tiles most decidedly need to go up to the fan and not just be a strip along the worktop.


Can you now spot wart three which resides on the right hand side of the kitchen?....yup, I stopped the tiles below the cupboards again and it looks odd.  I now have the job of having to fit some perfectly between the shelves - such fun, not!


Wart four is really more of a giant carbuncle which will be really hard for me to ignore.  If I have a particular feature or something I am fond of, like a a really nice fireplace or piece of furniture I learned very early in my dollhousing life to make sure it got placed pretty much back and centre of a room, so it could be admired by the large human.  Here I have made some lovely Elf units and terrific sink and cooker and microwave and wonderful resin counter tops and then carefully slid them all in sideways in a pokey room on the rooftop floor which is hard to see any way, so they are now pretty much unviewable.

Here endeth the lesson for this week  Think and plan, think and plan.

-----------------------------------------------------------------------------------------------------------------------

I have mentioned many times that my blog appears regularly each week on Saturday because I do a bit of work on the house and then write about it, so in a good week with lots of bits being done I might get two or three posts written and banked.  I have had as much as three months worth waiting to appear.  Sadly RL stuff has been getting in the way of late and so I am now all out of work and writing.  I will do my very best to get something done on the house next week and get a post to you on time and make it a happy one.  I just thought I would add a footnote in case Saturday came along and I didn't appear.

Thank you to all who comment here and to those who also email me.  It is always lovely to hear from you and to know my mini passions are also enjoyed at some level by others.  Basically it is lovely to share with such gentle souls.




Saturday 18 November 2017

A couple of purchases and starting fitting the kitchen

I have spent literally months trying to find a light with a fan like I have in the Rec room.  They don't turn up often and when they do they seem to be on American sites (Ebay included) this means the cost has been well over the twenty pound mark and as much as about forty pounds.  I wanted it but not that much.

One iPad and settee night I went on the usual trawl and for some astonishing reason found this on Maple Street Dolls House and Miniatures.  It is a site I sort of know but for some reason had never pinged in my searches before as having 'a light with fan'.  Not only did they have one but it was only £5.39 plus postage and came in a couple of days.  Whoops of happy could be heard in the land.  I am sharing this in case they have something you thought you couldn't find??????


It looks huge here but that's just a perspective thing, the scale is fine.





Another very considered purchase was this not too lovely corner sofa.  I knew it was low quality but it is the size and shape I want.  I had already looked at tons of mini sectional sofas all at daft prices and they would definitely need recovering and were mostly too big for my apartment space. 

I have already bought several very nice (expensive for me) retro pieces of furniture for this room but when I put them in place they looked far too OTT for a (mature) student flat.  My landlady is not that generous.  That said, a white corner sofa might still suggest a case of style over substance. Not at all practical. So, it may end up being recovered charcoal grey especially  if I can't tidy up the bits and bobs that need doing.  Think it also needs better/taller legs.  It is covered in a very, very thin velvet like material, so there are a ton of loose bits.  I am hoping a soft brush and some fray stop may improve it.  You can find it in several places but my favourite vendor had it cheaper than anyone else and it was here the next day, good old  Elf miniatures




----------------------------------------------------------------------------------------------------------------

Off we go on the process of getting the kitchen units in place.  


trims painted and ready to go

floors - two coats of satin varnish rubbed down before and in between

wallpaper template of kitchen floor

double sided sticky tape ready

kitchen and sitting room floor laid down

this is why I always use coving - I hate those gaps

I needed a silver escutcheon for front door lock.

The entrance to the flat is of course an interior door in the house but it would still need a (privacy) lock.  I thought a straightforward key lock would do rather than a Yale like we have on the front door of the house.  I started with brass escutcheon, covered it with silver pen, snipped out and super-glued it on the door.


coving in, door in, floor in, ready for units

sad face
I spent a lot of money getting the wallpaper for the sitting room and the tiles for the kitchen all the way from Australia and now I don't like it.  I was expecting flat mat wallpaper and a gloss card (maybe even embossed) printed tile.  I received all the same A3 size glossy paper for both.  I don't want shiny wallpaper and I do want thicker and embossed tiling.  

I tried scoring a strip of the tiles to emboss it a little.  The strip on top has been scored by me but it doesn't look substantially different to the flat piece underneath - so that's not the answer.


In real life I never have tiles in the kitchen - I can never find ones I want to live with for years and can never decide where to stop and start them - guess what - I am having just the same issues in small world.

I show you how it all turned out next week.

Glum mini person......




Saturday 11 November 2017

The not-much-fun bedroom

For some reason this apartment bedroom seemed to be a pig of problem from start to finish.

First of all there were six pairs of LED lights wires lying across the floor from the ceiling below.  They each had the neck of the fitting slightly protruding above the floor. Rather than making six deep grooves to get the wires and neck laid down properly I worked out a different tactic - a false floor.

I bought some 1/8th inch strips of wood from Hobby's  and used them like joists.  I put a strip right round the edge of the room, laid three inside this frame front to back and put in the occasional strip across (for additional support) where the wires would allow.  On top of this I glued a sheet of cardboard (thin but fairly rigid) for the new floor.

So all that worked out reasonably OK and I photographed each step of the way for this how-to-do-it post - then I wiped the card in the camera thinking I had downloaded the photos - I hadn't.

Here is the finished front edge - now that's a useful tutorial.



the edge of the false floor

I then wallpapered and added the usual coving but held off on the skirting.  Much ifs and ands and buts went into the decision to put carpet down first and then add the skirting.  I like realism and, in real life, carpet certainly goes down after the skirting is in place, but I had the sense to realise that my carpet would fray a good deal and the edges would never go down neatly  Any way when I look at my RL fitted carpet it is sort of almost rolled over at the edges to make a neat edge and it looks like the skirting is sitting on top of it.

I have never carpeted a room in a dollshouse - no, I couldn't believe it either.  I found it something of a pain to do.  The carpet seemed to stretch every which way and cutting it to fit round the door and door frames, trying to make that a nice tidy fit, was a pain; not to mention just getting the front edge to end up exactly in the right place.  Once I had got the front edge OK I daubed it with fray stop and gently 'pushed' it into the pile with my finger.  It seems to be holding OK so far.  I used the usual double sided tape but I only added it as I went along so the fabric didn't catch where I didn't want it to as I worked.

Down went the skirtings.  Ta dah - the end?...... not so, I had always planned a door at the back of the room to go to a bathroom.  Moral dilemma....... leave everything as it is (no-one else knows there 'should' be a door) or find a way to cut out a piece of the skirting (perfectly) and shove the door in.


paper and trims all in place

I used a knife with a broad edged blade like a chisel and hacked away at the wood.  It took absolutely ages. I thought that levering the whole piece of skirting out to cut out the piece would make such a mess of the wallpaper and the adjoining skirting so I wasn't prepared to risk it.  Finally I had hacked through to the back wall in both places and I levered out the door size section using a small screwdriver - out popped the whole skirting clean as a whistle.  Fortunately there was no collateral damage other than some wallpaper torn and the door would cover that any way!! So I removed the piece and duly glued the two sections back in again.

In went the door into the newly created space.....


ditto above plus false door


Here is the furniture I have so far for this room.  There will be a small matching side table and a plain small table to fit in the dormer window space for a desk and a chair for that.  The wardrobe and drawers do open.  Unlike some mini friends I may resist the temptation to fill them.....I love the idea but not the cost.  It would be a delight for anyone 'playing' with the finished house to discover such things but, sadly,  that won't happen.  I have never kept a house to 'play' with.  I really like the making and moving on.  That said, this one was meant to be my first keeper, so you never know.







(05/10/17)

Saturday 4 November 2017

ELF kitchen, right side

Day four


 I'll try and give you some tips (learned by my not doing it right!) in this post which will apply to all sorts of assemblies not just an ELF kitchen kit.

I started today with the fun part and made the stainless steel sink to go under the worktop.  This was super easy - basically just build a box and line with metal.  The contact adhesive (Bostik's Evostik) is pretty smelly and not the easiest to handle but don't try using another glue.  Metal to wood really does need a contact adhesive.  Do put a thin coat on both surfaces and wait for them to dry - about five minutes and then press together.  When I did the fridge I soon learned that my notion of just adding the glue to the metal side and not waiting very long, really doesn't work well.




When you have covered the surfaces with the film, if there are any teeny, tiny gaps that offend just use my usual method of filling them in with tiny blobs of white paint. This photo is a bit messy as the fill in needs to dry and a bit more trimming needs to be done, but the end result is nigh on perfect.




This photo shows the various stages involved.  The boxes are built and everything has one good coat of paint to help the plastic stick - don't miss out this stage - even if the plastic appears to stick OK it will gradually pull away from unprimed wood.  Cut a load of strips of plastic ready for covering the sides and fronts as needed and then start wrapping.  Trim any excess with a very sharp knife rather than scissors.  Take care to remember not to cover any areas which are going to be stuck to something else.





Day five
All the pieces were prepped and ready to assemble.

If you have several doors to space out - do the ones at each edge first and then space the others evenly between.


If you have cupboards above lower units stand them on top of the bottom units and get the upper cupboards lined up perfectly with the ones below, before gluing them in place





Unlike me.... Do not cut any shelf that is going in a space before the space is made, it is very likely to be too big or too small for the finished gap. (How do people like Elizabeth always get theirs spot on?) Even a tiny amount like this means (of course) that you can't fix it in place.




I always make a template from a piece of card for positioning the handles so they all line up and match each other.  It is as simple as making a cardboard cutout the same size as the door, positioning the handle on this and marking up where the holes need to go.  I then drill a hole through the cardboard and double check before using it on the doors.  At this scale the slightest deviation form the vertical (or horizontal) will really shout at you.


The shelf was a change of plan.  I had ordered an LED to go over the sink but at the eleventh hour I decided the complications involved in getting the wiring in and, worse, out the back of the house, didn't warrant the effect I would get from it.  Also the kitchen is so small it doesn't give any real space to be able to dress it with stuff dotted about so I am happier to have a shelf to put something on.

Tah dah...... the units for the right side of the kitchen are ready.




If you like the wonderful kits that ELF makes don't be nervy about putting them together, the first time will be a bit of a challenge (honestly not much) and then, after that, it is always plain sailing and you will be thrilled at how clever you are and how lovely the kits are.

(09/09/17)